消防隔热服的用途和使用范围
DFXF-93-A型消防隔热服采用纤维织物与镀铝薄膜的复合材料制作，服装包括上衣、裤子、手套、头罩和盖脚，不含石棉，具有双重轻、强度高、阻燃、耐高温、抗热辐射、耐磨、耐折以及对人体无毒害等优点，能有效地保障消防队员和高温作业人员不被烈焰、高温灼伤。能有效地保障消防队装备质量监督检验中心检测合格，符合GA88《消防隔热服性能要求及试验方法》的要求。船用防护服经中国船级社检验。
消防隔热服的主要技术参数
序号 | 名称 | 技术参数 |
1 | 撕破强度 | ≥ 32N |
2 | 剥离强度（ N/30 ㎜） | ≥ 9N |
3 | 阻燃碳长（ 2s ） | ≤ 1000㎜ |
4 | 抗渗水性能 | ≥ 4000Pa |
5 | 面料反射率 | 波长400-1000mm,全反射>70%,漫反射>40% |
6 | 面料阻燃性 | 碳长<1000mm |
7 | 面料的撕破强力 | >1000g/cm |
8 | 面料的剥离强度 | ≥12N/50mm |
9 | 面料的防水性 | 在2m水柱压力下不渗水,不破裂 |
10 | 隔热性 | 在温度850℃距火源1.75m时2min服装内表面温度不大于45 |
正在折叠打包的消防隔热服
使用及保养：
1.使用前应认真检查隔热服有无破损。
2.使用时按常规着装，靴子、脚套应穿在裤筒里面，应扣上所有搭扣。
3.消防隔热服具有优良的阻燃隔热性能，但不可能在所有条件下都能起到护人的作用，在靠近火焰区作业时，应尽量避免使服装与火焰和溶化的金属直接接触。在有化学气体和放射性伤害的条件下使用时，均须配备相应的配件和正压式呼吸器。
4.使用后应用软刷、中性洗涤剂洗刷表面，然后用清水冲洗干净。洗净后在通风处自然晾干，严禁用水浸泡和重击。
5.消防隔热服应存放在通风干燥处，以防受潮后复合层脱落。
6.消防隔热服使用有效期三年。
隔热服车间一角
主要技术性能：
组成：每套由头盔、头套、上装、裤子、手套、脚套、消防员靴组成。
面料的反射率：波长400—1000mm全反射70％、漫反射40％
面料的阻燃性：碳长＜100mm
面料的撕破强力：＞1000g/㎝
面料的剥离强度：≥12N/50m
面料的防水性：在2m水柱压力下不渗水、不破裂。
隔热性：在温度850℃，距火源1.75m处历时2min，服装内表面温度不大于45℃。
绝缘性：手套手掌部位试验电压大于5000V。
可见视野大于120°。
穿着人员身高：1.6～1.8m.。
重量8㎏。
本产品得到中华人民共和国船检局认可，它不仅适用于船用消防，而且也可用于陆地上的救火作业，是消防队员理想的个人保护装备。
英文说明书
DFXF-93-A
PROTECTIVE CLOTHING FOR FIRE-FIGHTING
INSTRUCTIONS
Model DFXF-93-Afireman’s protective suit is made of new fireproof fibre and aluminium-plated film composite according to the requirements of SOLAS1974 that is amended in 1981. It is characteristic of radiation resistant of heat, fireproof, heat insulation, waterproof insulation softness, high strength, corrosion resistance and dissolution residue resistance to all kind of acid, alkali and organic solvent. The product has been tested and certificated by the marine inspection of the people’s republic of china, that it can be used for fire fighting on the ground as well as for maring fire fighting. It is good for fireman as protective equipment.
Main Technical Property
- 1. Consist: each suit consists of helmet, jacket, trousers, gloves, socks and shoes.
- 2. Reflectivity of cloth: wavelength at 400-1000mm, total reflection is 70％; diffuse reflection is 40％.
- 3. Fireproof of cloth: carbon length＜100mm
- 4. Tearing strength of cloth:＞1000g/cm
- 5. Peel strength of cloth:≥12N/50mm
- 6. Water resistance of cloth; without being seeped or broken under 2m of hydraulic pressure
- 7. Heat insulation property: the inner surface temperature≤45℃ when taking a period of time about 2 minutes at the temperature of 850℃ and at the distance of 1.75m from the fire source.
- 8. Insulation property: testing voltage＞5000v at palm position of the glove.
- 9. Viewing angle: ＞120°
- 10. Height of fireman: 1.6～1.8m
- 11. Weight:8kg
Use and care
- 1. Inspect the suit carefully if it is damaged or not before wearing.
- 2. Wear the suit follow the routine that shoes and socks should be wom inside the trouser legs and all buttons should be done up.
- 3. Although the suit has fine property of fireproof and heat insulation, it is impossible to protect the fireman in all instances. Try your best to turn the suit away from being contacted directly with fire or molten metals when working near the flame. Proper fittings and positive pressure breathing-instrument should be equipped under the condition of chemical gas or radioactive harm.
- 4. Clean the surface of the suit with soft brush and neutral detergent after using, and then rinse it with clean water. Dry the suit in the air and avoid moisture after cleaning. Dunking the suit or hard attacking is prohibited.
- 5. the fireman’s protective suit should be put in a dry place with air through to prevent the composite layer from falling off the suit after damped.
- 6. Expiry date:three years